Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
How do you actually feel in relation to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't exactly rocket science, yet it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard project. If the old tub is conveniently easily accessible, the task can move immediately; if you have to open a wall to remove the old tub and position the new bath tub, the job is much harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require a helper to vacate the old bathtub as well as set in the new one. Make certain you have qualified yourself for the task and are comfortable trying it. As opposed to employing a service provider to take over a halfway-completed task, it is far better to take into consideration utilizing one prior to you begin. Opportunities are you might require a professional plumber to make tube links.
This short article will certainly help you mount a brand-new bathtub in your shower room if you have already bought a new bathtub and also do not require to alter the setup of your previous water supply pipes.
Your devices and material checklist ought to consist of the following:
Planning for the Installment
To start with, the sustaining structure supplied with the bathroom must be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both faucets utilizing 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing faucets can be fairly bothersome due to the limited accessibility that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. Once the supply pipes have been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before carrying on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, put the bathtub in the needed position. The wood boards are handy in uniformly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little points.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the furthest flexible faucet adapter to the proper supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply and check all joints and new pipework for leaks as well as tighten them if necessary. Fill the bath tub and additionally check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's instruction manual. Tiling and securing around the bathtub needs to wait till the bathtub has actually been used a minimum of once as this will certainly resolve it into its final placement.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end provides a link to the current supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washers are in area in between the tap as well as the sink. Secure the faucet in position with the producer offered backnut. When the faucet is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the tap ends initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture an inflexible seal, causing the water to penetrate the wall surface in between the bath and also the tiling, causing complications with moisture and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are offered in tubes and cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always load the bath tub with water before sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not consider this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that review about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the search engines. Enjoyed our write-up? Please share it. Help someone else discover it. Thanks a lot for your time. Kindly visit our website back soon.
Burst? Reach us! Report this page